“SILE” and “CELLINA” •  Standard Nozzles

The “Sile”  and  “Cellina” , Series nozzles, manufactured in hardened alloy steel, are designed for general pipe clearing requirements.

Maximum pressure 300 bar.

Part Number

Angle of rear jets

Type of Rear Jets

Type of Front Jet

Min LPM

Working Diameter

Connection

5500.07

35°

Drilled

*

12

20 – 60 mm

1/8” F

3518.00

35°

Drilled

*

12

30 – 100 mm

1/4” F

3519.00

35°

Drilled

*

31

35 – 140 mm

3/8” F

5520.30

35°

Drilled

 M6x8 **

42

50 – 200 mm

1/2” F

5520.60

35°

Drilled

M6x8 **

72

80 – 250 mm

3/4” F

5520.70

35°

Drilled

 M6x8 **

72

100 – 350 mm

1” F

** If the front orifice is not required ,  use the plug furnished with the nozzle.

Applications:

Drains.

Small pipes with limestone, soap and grease build-up.

General pipe clearing applications.


“LIVENZA” and “MEDUNA” Series . Thrust Nozzles

“Livenza” and “Meduna”  are designed for applications where high thrust is required. Meduna series is made of hardened stainless steel. Livenza is made of hardened alloy steel.

Maximum pressure 300 bar.

Part Number

Angle of rear jets

Types of rear jets

Type of front jet

Min LPM

Working Diameter

Connection

3520.210

25°

Drilled

M6x8**

42

50 – 125

1/2” F

5515.30

15°

Drilled

M6x8**

42

50 – 200

1/2” F

5515.60

15°

Drilled

M6x8**

72

85 – 250

3/4” F

5515.70

15°

Drilled

M6x8**

72

100 - 300

1” F

** If the front orifice is not required ,  use the plug furnished with the nozzle.

Aplicaciones

Drains and high columns.

General fase pipe clearing applications.


“VORTEX” Series     Combined Jet-Angles Nozzles

The “Vortex”  series nozzles, manufactured in hardened alloy steel with 8 rear jets at two different angles, are desgined for cleaning pipes with grease and soap accumulations. The combined angles of the jets offer optimal thrust, impact and cleaning efficiency.

Maximum pressure 300 bar.

Part Number

Angle o f rear jets

Type of rear jets

Type of front jet

Min LPM

Working Diameter

Connection

5528.50

15° + 35°

Drilled

M6x8

83

50 – 150

1/2” F

5532.50

15° + 35°

Drilled

M6x8

102

80 – 200

3/4” F

5533.50

15° + 35°

Drilled

M6x8

155

100 – 400

1” F

** If the front orifice is not required ,  use the plug furnished with the nozzle.

Applications:

Pipes with accumulation of grease and soap build-up.

Drains and high columns.

Easy retrieval from illegal pipes


“RONDÒ” Series . Fan-Jet Nozzles

The “Rondò”  series nozzles, perform with the same clearing results of the rotating nozzles, without loosing the impact force due to the spinning effect.

Its fan-jets always work at 360º uniformly throughout the incide of the pipe, cutting and removing hard deposits encrusted at the wall of the pipe. The nozzle´s propultion is effected by three rear jets.

Maximum pressure  300 bar.

Part Number

Angle of rear jets

Type of rear jets

Type of front jet

Min LPM

Working Diameter

Connection

3580.01

18° + 45°

M6x8 Orifices (3) + Fanjets (8)

No

75

50 – 200

1/2” F

3580.05

18° + 45°

M8x8 Orifices (3) + Fanjets (8)

No

170

70 – 350

3/4” F

3580.10

18° + 45°

M8x8 Orifices (3) + Fanjets (9)

No

242

75 – 450

1” F

3580.20

18° + 45°

M12x12 Orifices (3) + Fanjets (12)

No

375

130 - 550

1” ¼” F

Applications:

Lines with accumulartions of soap, grease and rubber.

Through clearing for video inspection .

It utilizes 100% of the water flor rate.


“ARZINO” Series    Ellipse nozzles

The “Ellipse”  series nozzles are manufactured in hardenes alloy steel or stainless steel. The particular shape of these nozzles allows easy penetration through tight elbows and provides easy retrieval from the pipe.

Maximum pressure 300 bar.

Part Number

Angle of rear jets

Type of Rear Jets

Type of Front Jet

Min LPM

Working Diameter

Connection

5526.00

15°

Drilled

M4x5

25

30 – 80

1/4” F

5527.00

15°

Drilled

M4x5

25

60 – 120

3/8” F

5528.06

15°

M6x8

M6x8

57

60 – 200

1/2” F

5532.06

15°

 M6x8

M6x8

75

100 – 250

3/4” F

5533.06

15°

M6x8

M6x8

102

150 - 350

1” F

** If the front orifice is not required ,  use the plug furnished with the nozzle.

Applications:

Clearing of pipes where high rust is required.

Pipes with sharp turns and/or heavy build-up.


“RAUT” Series •  Tri-Head Nozzles

The “Raut”  Series nozzles, manufactured in hardened allow steel with 4 front jets, are designed for high penetration power when it is crucial to break through blocked material.

Due to the strong penetration power, caution must be used in plastic pipes.

Maximum pressure 300 bar.

Part Number

Angle of Rear Jets

Type of Rear Jets

Type of Front Jet

Min LPM

Working Diameter

Connection

5550.00

25°

Drilled

1 @ 0° + 3 @ 15°

45

30 – 80

1/8” F

5550.05

25°

Drilled

1 @ 0° + 3 @ 15°

68

30 – 100

1/4” F

5550.10

25°

Drilled

1 @ 0° + 3 @ 15° M 4x5

83

50 – 150

1/2” F

5550.20

25°

M 6x8

1 @ 0° + 3 @ 15° M 6x8

113

80 – 300

3/4” F

5550.30

25°

M 6x8

1 @ 0° + 3 @ 15° M 6x8

140

100 – 400

1” F

5550.40

25°

Drilled

1 @ 0° + 3 @ 15° M 6x8

200

150 - 500

1 ¼ ” F

Applications:

Pipes with heavy blockages.

Renoval of stones and ice.

General pipe cleaning applications